If you want to hack your Xbox 360 and your dashboard version is over 7371 then the only way that you can hack it is with the reset glitch hack (RGH). When I started looking for a way to hack my 360 I heard about the jtag method only to find out that my dashboard was newer then 7371, but in early September a hardware exploit was developed know as the RGH. Basically what the RGH does is send a single to the processor that tells it to reset. Usually it would do exactly that however if the single is sent when it is booting up it allows us to run unsigned code.
to perform this RGH and utilize the exploit what you will need to do is read the NAND, install the modchip, write the NAND and installing your dash board of choice (i will be using xexmenu).
To do this you will need:
modchip (i will be using the coolrunner from team-xecuter)
coolrunner LPT program cable
male LPT port (printer cable) (x1)
wires (x12 this will be your LPT cable so make them long)
computer with a female LPT port
a program to read the NAND (i used nandprob 2 you can find it HERE)
soldering iron
solder
Jtag tool (software)
360gcprog (software)
flux (not needed but HIGHLY recommended)
***Disclaimer: I am not liable for any damage that may be caused to your property or self from following the instructions in this tutorial. Soldering irons can be very hot and cause burns, as well as possibly break your Xbox 360. Opening your xbox 360's shell will void its warranty. ***
now then lets get started. Cast software vs sonar cakewalk contact. first you need to completely take apart you 360 there are plenty of guides to do that so i wont cover it here. When the case is removed it should look like the picture. i highly suggest that you take off the metal case it sits in so that you can access the bottom of the motherboard.
to perform this RGH and utilize the exploit what you will need to do is read the NAND, install the modchip, write the NAND and installing your dash board of choice (i will be using xexmenu).
To do this you will need:
modchip (i will be using the coolrunner from team-xecuter)
coolrunner LPT program cable
male LPT port (printer cable) (x1)
wires (x12 this will be your LPT cable so make them long)
computer with a female LPT port
a program to read the NAND (i used nandprob 2 you can find it HERE)
soldering iron
solder
Jtag tool (software)
360gcprog (software)
flux (not needed but HIGHLY recommended)
***Disclaimer: I am not liable for any damage that may be caused to your property or self from following the instructions in this tutorial. Soldering irons can be very hot and cause burns, as well as possibly break your Xbox 360. Opening your xbox 360's shell will void its warranty. ***
now then lets get started. Cast software vs sonar cakewalk contact. first you need to completely take apart you 360 there are plenty of guides to do that so i wont cover it here. When the case is removed it should look like the picture. i highly suggest that you take off the metal case it sits in so that you can access the bottom of the motherboard.
Note If you receive an error message when you run the Xbox Live connection test, see the Xbox Live Connection Error Solution for troubleshooting steps.
Demonter, xbox,360,slim - Dailymotion [TUTO] Flasher le lecteur de sa Xbox 360 SANS DEMONTAGE - Le. Comment ouvrir l.alimentation Xbox 360 [Resolu] - Comment Ca Marche. Bonjour ou bonsoir, voila l.alimentation de ma xbox 360 a griller a cause d.une euh on ne vous avez gere demande comment demonter une xbox 360. TUTO - Demonter sa PS3 Slim de A. Can u jtag a 4gb xbox 360 slim? Discussion in 'Xbox 360 Support Archive' started by toolegit, Aug 12, 2011 with 16 replies and 11,120 views. Slim xbox's came with 9199 at launch, you need 7371 or lower to jtag, therefor not possible (as of now). Dr Death, Aug 12, 2011. Bonjour, je voudrais savoir comment cracker ma xbox 360 arcade sans l'ouvrir peut-on mettre des jeux sur dique dur et que la xbox les reconnaissent ou les graver je voudrais savoir comment y.
- Select Yes if you are prompted to update console software. Note If you receive an error when you try to update the console software, see Error code after console software update.
If you need help setting up your wireless connection for the first time, see the Xbox Live First-Time Connection Solution.
If you've been able to connect wirelessly in the past but can't connect now, see the Xbox Live Connection Solution.
If your wireless network doesn't appear under Available Networks, see the Wireless Network Connection Solution.
How to fix entry qpst download cherry mobile flare. Manually configure your wireless network settings
To manually configure the wireless network settings for your Xbox 360 console, follow these steps.
Xbox 360 Slim Amazon
Warning Incorrectly-configured wireless network settings can negatively impact your console’s performance. Pirates of the caribbean isles of war hack download. We recommend that only networks specialists follow these steps, and only in cases where your network requires manual configuration to connect to the Internet. In most cases, you will get the best results by using the automatic settings.
Xbox 360 Slim Red Dot
Cracker Xbox 360 Slim Sans L'ouvrir
- From the Dashboard, go to settings, then select System.
- Select Network Settings.
- Select your wireless network.
If you're prompted for your pass phrase or key, enter it and then select Done. After the Network Status test completes, select Continue and then select your wireless network.
Note If you receive an error message when you run the Xbox Live connection test, see the Xbox Live Connection Error Solution for troubleshooting steps. - Select Configure Network. Now you can manually configure your IP settings, your DNS settings, your PPPoE settings, or your MAC address.
See the steps below for the settings you want to configure.Manually configure your IP settings- On the Basic Settings tab, select IP Settings.
- Under Edit IP Settings, select Manual.
- To manually set your IP address, select IP Address, enter the IP address, select Done, and then select Done.
- To manually set your subnet mask, select Subnet Mask, enter the subnet mask, select Done, and then select Done.
- To manually set your gateway, select Gateway, enter the gateway address, select Done, and then select Done.
Manually configure your DNS settings- On the Basic Settings tab, select DNS Settings.
- Under Edit DNS Settings, select Manual.
- Select Primary DNS Server, enter the primary DNS server address, then select Done.
- Select Secondary DNS Server, enter the secondary DNS server address, select Done, and then select Done.
Manually configure your PPPoE settings- Under Configure Network, select the Additional Settings tab.
- Select PPPoE settings.
- Select User Name, enter the PPPoE user name, then select Done.
- Select Password, enter the PPPoE password, then select Done.
- Select Service Name, enter the PPPoE service name, select Done, and then select Done.
Manually configure your MAC address- Under Configure Network, select the Additional Settings tab.
- Select Advanced settings.
- Select Alternate Mac Address, enter the MAC address, select Done, and then select Done.
Manually configure your host name Driver scanner discovery 1200 ub plus win 7.- Under Configure Network, select the Additional Settings tab.
- Select Advanced settings.
- Select Host Name, enter the host name, select Done, and then select Done.